The following article is about how to remove a hard drive from an HP laptop at home. The material also provides detailed instructions on how to properly disassemble the computer case.
Eject disk
Before you remove the hard drive from the laptop, you need to prepare everything. To begin, complete the running processes and programs so that the device can turn off quietly and quickly.
After this, disconnect all connected media and peripherals. Also pull out the power cord so that it does not interfere with the further procedure. After making sure that the device is completely turned off, you can proceed with the implementation of the instructions on how to remove the hard drive from the laptop.
Turn it upside down and lay it on a flat surface to avoid various damage. Lay a thick cloth to protect the screen cover. Next, slide both clamps holding the battery inside, pull it out of the case.
Before removing the hard drive from the laptop, find the orange latch inside. Hold it with one hand and gently press the other against the back of the device cover. Pressure should go upward. Take care not to break it. After it is completely removed, find the black film. It must be removed before you remove the hard drive from the HP laptop.
After access to the solid state drive is obtained, carefully grasp the small tab that is located on the plug of the hard drive cord. After that, start pulling up. Do this until the cable is completely disconnected from the connector. Use a screwdriver and remove the screws that secure the hard drive. How to remove this part from the laptop? Just gently pull it up until it is completely removed.
Now you need to perform the replacement procedure. Place the new SSD inside the dedicated slot where the obsolete part was located. Replace the screws to secure. Connect the cable to a dedicated channel. Insert the plug until you hear a click.
After you removed the hard drive from the laptop, replaced it, are ready to tighten the case, check again that everything is installed correctly and firmly. Otherwise, malfunctions may occur.
If everything is as it should, put the back cover in its original place until it clicks and screw it. Make sure there are no gaps anywhere. Replace the battery. Connect the power cable and peripherals.
Turn on the computer and check it is working. If all is well, then the drive is installed correctly, now you know how to remove the hard drive from the laptop.
Next, we move on to instructions on how to disassemble it.
Preparation
First of all, you need to completely turn off the computer again and turn off all peripheral devices. Select a flat surface, lay a thick cloth on it so as not to damage the screen cover. Before disassembling an HP laptop, you should either make a schematic drawing of its back, or take a picture of it, so that later you can correctly reinstall all the removed screws. This tip will greatly facilitate your work.
Removing attachments
On the back of the laptop there are special compartments that allow quick access to network modules, a solid-state drive and RAM dies. Their covers can be removed quite easily after the bolts are unscrewed. Sometimes a simple relaxation is enough. After these parts are removed, carefully remove the optical drive.
Fix fix
Now you need to unscrew all the fastening screws that are located on the back of the laptop.
Attention! When removing the bolts, do not forget to lay them out according to the scheme that was prepared in advance so as not to confuse or lose anything.
After this procedure is complete, inspect the back to make sure that you have unscrewed everything you need. If any of the bolts go unnoticed, then the parts are almost impossible to remove, due to which the case may be damaged.
Keyboard Removal
Before disassembling your HP laptop, make sure that this panel is not divided into two independent parts. Next, using a flathead screwdriver, carefully pry up the upper right corner of the keypad. Move to the left and gently release the remaining restraining elements. If your model does not have a monolithic panel, then first remove the top deck. Also check for metal latches and holding tape.
When removing the keyboard, try not to make sudden movements, you can inadvertently break the cable.
Disconnect Connectors
Under the dismantled keyboard module are loops of connections. Three of them are standardly installed. Disconnect the two touchpad connectors and the USB power connector from the motherboard. Now you can remove the top cover of the laptop.
You can move on to the most important and difficult part of disassembling a laptop - the process of removing the motherboard.
Procedure execution
In order to remove this important part and not cause any damage, it is necessary to carefully unscrew all the screws that fix the elements, and then carefully disconnect all the cables and connectors.
Next, carefully remove the system board from the laptop. In the event that force has to be used in some place, stop the procedure and check the surface for any remaining loose screws.